Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You might discover that your garage door opener has been offering you issues, so you require to fix it. You can fix it by changing a circuit card, a photo-eye sensing unit, the main drive gear, or the set-limit switches. You can additionally check if the safety sensors are functioning appropriately.

Changing a circuit card

Changing a circuit board for your garage door opener requires a few actions and also tools. Initially, you need to turn off the breaker and also disconnect any kind of cables. Next off, open up the motherboard cover. This will assist you to diagnose the issue and also figure out if you require a brand-new board. Next off, eliminate the old board and also its cord connectors.

You can then continue to replace the motherboard. The replacement process is very easy and takes around 10 minutes. A new circuit board will certainly set you back about $80. To protect your new circuit board from power rises, you can buy a rise protector.

Replacing a photo-eye sensing unit

Changing a photo-eye sensor can be a rather simple job. Initially, eliminate the sensing unit from the door as well as ensure it is located appropriately. If the sensor is angled whatsoever, it may not be receiving the right signal, which might be triggering the strobe lights. If you discover that the photo-eyes are out of alignment, you might require to have actually a specialist come and also fix the problem.

The photo-eye sensing unit includes two items that install on the outside of the door tracks and toward the floor. The image eyes will have a small LED light and also should be strong in shade. If the light is blinking, its likely the photo-eye is malfunctioning as well as will require to be changed.

Changing a major drive gear

To replace a garage door opener major drive equipment, start by removing the cap from the chain pulley. Next off, get rid of both screws holding the drive gear to the gear setting up. Currently, you can loosen the three tension pins. Press them from both sides and afterwards eliminate them. Then, disconnect the three cables from the garage door opener electric motor. These wires should be white, red, and also blue.

As soon as you have removed the old equipment, mount a new one. Make certain to oil it well. Place the brand-new equipment into the shaft, making sure to align the installing openings. Make sure the gear as well as gear assembly are located appropriately to ensure smooth procedure. Next, utilize a hammer and also a nail to drive a pin right into the brand-new gear.

Adjusting the set-limit switches

The first point you ought to do if your garage door is not working properly is to check the set-limit buttons. You might need to readjust them to make sure that the door shuts earlier or quits before it reaches the flooring. You can examine this by checking out your garage doors manual or online.

To adjust the set-limit switches, youll require a screwdriver or outlet. Readjust the handle clockwise or counterclockwise until the door moves up and quits, or lowers its range. To look for correct travel range, determine the gap from the bottom of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Key St Ste 105, Keller, TX 76248, United States

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *


Back To Top